 Using a F6 Driver with USB Floppy, This is the fix for using USB Floppy drives for F6 drivers in Textmode |
  |
  Sep 14 2006, 02:35 PM
Post
#1
|
|
|
Group: Members Posts: 4 Joined: 14-September 06 Member No.: 110320 
 |
This fix will add support for USB floppy disks in the text mode portion of Windows Setup, and allow you to load F6 drivers.
This fix should work on Windows 2000 and up. I have only tested it with a Sony USB floppy drive on Windows XP and Windows Server 2003 x64 EDIT: Thanks go out to everyone who has added more drives to this fix. --- Windows Setup F6 USB Floppy Drive Fix Create your Storage device driver disk and open textsetup.oem Add the following lines to the bottom of [HardwareIds.scsi.(device name)] If this section does not exist you must create it! If your USB floppy drive still does not work, look for the hardware ID in the floppy drive driver's .inf file, and make sure any legacy floppy drives are disabled in the bios. CODE id = "USB\VID_03F0&PID_2001", "usbstor" #--HP id = "USB\VID_054C&PID_002C", "usbstor" #--Sony id = "USB\VID_057B&PID_0001", "usbstor" #--Y-E Data id = "USB\VID_0409&PID_0040", "usbstor" #--NEC id = "USB\VID_0424&PID_0FDC", "usbstor" #--SMSC id = "USB\VID_08BD&PID_1100", "usbstor" #--Iomega id = "USB\VID_055D&PID_2020", "usbstor" #--Samsung Here is an example file CODE #//////////////////////////////////////////////////////////////////
[Disks] d1 = "Intel Embedded Server RAID Technology",\MegaSR,\ [Defaults] scsi = MegaSR [scsi] MegaSR ="Intel Embedded Server RAID Technology (Windows XP/2003 64-bit)", MegaSR [Files.scsi.MegaSR] driver = d1, MegaSR.sys, MegaSR inf = d1, MegaSR.inf inf = d1, NODEV.inf catalog = d1, MegaSR.cat [HardwareIds.scsi.MegaSR] id="PCI\VEN_8086&DEV_2682&SUBSYS_10901734", "MegaSR" id="PCI\VEN_8086&DEV_2683&SUBSYS_10901734", "MegaSR" id="PCI\VEN_8086&DEV_2682&SUBSYS_81FF1043", "MegaSR" #--The following lines give additional USB floppy support id = "USB\VID_03F0&PID_2001", "usbstor" #--HP id = "USB\VID_054C&PID_002C", "usbstor" #--Sony id = "USB\VID_057B&PID_0001", "usbstor" #--Y-E Data id = "USB\VID_0409&PID_0040", "usbstor" #--NEC id = "USB\VID_0424&PID_0FDC", "usbstor" #--SMSC id = "USB\VID_08BD&PID_1100", "usbstor" #--Iomega id = "USB\VID_055D&PID_2020", "usbstor" #--Samsung [Config.MegaSR] value = "Parameters\PnpInterface", 5, REG_DWORD, 1 #////////////////////////////////////////////////////////////////// This post has been edited by spiff: Oct 31 2006, 12:50 PM |
 |
 
|
|
Sep 26 2006, 08:45 AM
Post
#2
|
|
|
Group: Members Posts: 1 Joined: 26-September 06 Member No.: 111368 
|
You are an absolute legend man. I googled everywhere for the answer to this, and it was all about slipstreaming the drivers to a new WinXP CD. Cheers man you saved me so much time.
|
|
|
|
|
Oct 8 2006, 09:27 PM
Post
#3
|
|
|
Group: Members Posts: 4 Joined: 14-September 06 Member No.: 110320
|
That's exactly why I made the fix, I searched everywhere for a solution, and after about a day of research I reaized the txtsetup.oem used the same formatting as txtsetup.sif. Which made sence since MS likes to recycle code. This fix is more intened for people who can't make new windows CDs, like me. I couldn't make a new windows setup disc and tell my customer to install with it, not to mention the licencing issues. In a manufacturing setting this fix has saved me a ton of time.
This post has been edited by spiff: Oct 8 2006, 09:28 PM |
|
|
|
|
Oct 13 2006, 03:46 PM
Post
#4
|
|
|
Group: Members Posts: 4 Joined: 14-September 06 Member No.: 110320
|
It seems I left off the hardware id for NEC drives ( thanks to Greg for pointing that out)
Added Iomega drives ( thanks to Jammin ) updated list of hardware ids. CODE id = "USB\VID_03F0&PID_2001", "usbstor" #--HP
id = "USB\VID_054C&PID_002C", "usbstor" #--Sony id = "USB\VID_057B&PID_0001", "usbstor" #--Y-E Data id = "USB\VID_0409&PID_0040", "usbstor" #--NEC id = "USB\VID_0424&PID_0FDC", "usbstor" #--SMSC id = "USB\VID_08BD&PID_1100", "usbstor" #--Iomega |
|
|
|
|
Oct 13 2006, 05:27 PM
Post
#5
|
|
|
Update Packrat  Group: Members Posts: 323 Joined: 4-July 05 From: Riverview, MI USA Member No.: 62992 OS: XP Pro x64
|
I don't understand.
You're putting the newly modified driver on a floppy, right? So how will the floppy be read from when its driver is not installed yet? |
|
|
|
|
Oct 16 2006, 11:59 PM
Post
#6
|
|
|
Newbie Group: Members Posts: 48 Joined: 12-May 04 Member No.: 19767 |
Can this method be extended to support USB thumb drives or HDDs? THAT would be really helpful.
|
|
|
|
|
Oct 20 2006, 03:34 PM
Post
#7
|
|
|
Group: Members Posts: 4 Joined: 14-September 06 Member No.: 110320
|
vpn-user
I believe this method can be extended to USB thumb drives and USB hard drives, IF they are supported by the USBSTOR driver that is included in windows. You just need to find the hardware ID of your device, which can be found in the device manager. Look under the Universal Serial Bus controllers section for your device, goto it's properties, the details tab, then Hardware Ids, the bottom one should be the one you want. then just duplicate the formatting and add it to your txtsetup.oem file. I have not had a chance to test this, but I have loaded various other drivers via the F6 floppy method. 5eraph When text mode first loads, it lets the system BIOS tell it what the floppy drives are, but once text mode finishes loading windows it no longer sees the USB floppy drives as a legacy floppy drive, instead it sees it as a USB device. This fix works because it tells windows what the USB device is, it exactly the same a loading a regular Mass Storage Device driver, Windows knows the device is there, it just doesn't know what it is. I hope that makes sence. |
|
|
|
|
Oct 22 2006, 04:19 AM
Post
#8
|
|
|
Group: Members Posts: 2 Joined: 22-October 06 Member No.: 113687 
|
Am I doing this correctly? I use Freecom NEC USB floppy drive.
CODE [Disks]
D-I386-NT5-RAID="VIA V-RAID Driver Diskette",\I386\VIAMRAID, \I386\NT5 D-I386-NT4-RAID="VIA V-RAID Driver Diskette",\I386\VIAMRAID, \I386\NT4 [Defaults] scsi = VCOMBORAID_I386_NT5 [SCSI] VCOMBORAID_I386_NT5="VIA V-RAID Controller Series(Windows XP)" VCOMBORAID_I386_WIN2K="VIA V-RAID Controller Series(Windows 2K)" VCOMBORAID_I386_NT4="VIA V-RAID Controller Series(Windows NT4)" [Files.SCSI.VCOMBORAID_I386_NT5] driver = D-I386-NT5-RAID, viamraid.sys, CFG_NT5 inf = D-I386-NT5-RAID, viamraid.inf catalog = D-I386-NT5-RAID, viamraid.cat [Files.SCSI.VCOMBORAID_I386_WIN2K] driver = D-I386-NT5-RAID, viamraid.sys, CFG_NT4 inf = D-I386-NT5-RAID, viamraid.inf catalog = D-I386-NT5-RAID, viamraid.cat [Files.SCSI.VCOMBORAID_I386_NT4] driver = D-I386-NT4-RAID, viamraid.sys, CFG_NT4 inf = D-I386-NT4-RAID, viamraid.inf [config.CFG_NT5] value = parameters\PnpInterface,5,REG_DWORD,1 [config.CFG_NT4] value = "", Tag, REG_DWORD, 1 [HardwareIds.scsi.VCOMBORAID_I386_NT5] id = "PCI\VEN_1106&DEV_3349&CC_0104","viamraid" id = "PCI\VEN_1106&DEV_6287&CC_0106","viamraid" id = "PCI\VEN_1106&DEV_0591&CC_0104","viamraid" id = "PCI\VEN_1106&DEV_3249&CC_0104","viamraid" id = "PCI\VEN_1106&DEV_3149&CC_0104","viamraid" id = "PCI\VEN_1106&DEV_3164&CC_0104","viamraid" id = "PCI\VEN_1106&DEV_0581&CC_0104","viamraid" #--The following lines give additional USB floppy support id = "USB\VID_03F0&PID_2001", "usbstor" #--HP id = "USB\VID_054C&PID_002C", "usbstor" #--Sony id = "USB\VID_057B&PID_0001", "usbstor" #--Y-E Data id = "USB\VID_0409&PID_0040", "usbstor" #--NEC id = "USB\VID_0424&PID_0FDC", "usbstor" #--SMSC id = "USB\VID_08BD&PID_1100", "usbstor" #--Iomega [HardwareIds.scsi.VCOMBORAID_I386_WIN2K] id = "PCI\VEN_1106&DEV_3349&CC_0104","viamraid" id = "PCI\VEN_1106&DEV_6287&CC_0106","viamraid" id = "PCI\VEN_1106&DEV_0591&CC_0104","viamraid" id = "PCI\VEN_1106&DEV_3249&CC_0104","viamraid" id = "PCI\VEN_1106&DEV_3149&CC_0104","viamraid" id = "PCI\VEN_1106&DEV_3164&CC_0104","viamraid" id = "PCI\VEN_1106&DEV_0581","viamraid" [HardwareIds.scsi.VCOMBORAID_I386_NT4] id = "PCI\VEN_1106&DEV_3349","viamraid" id = "PCI\VEN_1106&DEV_5287","viamraid" id = "PCI\VEN_1106&DEV_6287","viamraid" id = "PCI\VEN_1106&DEV_0591","viamraid" id = "PCI\VEN_1106&DEV_5337","viamraid" id = "PCI\VEN_1106&DEV_3249","viamraid" id = "PCI\VEN_1106&DEV_3149","viamraid" id = "PCI\VEN_1106&DEV_3164","viamraid" id = "PCI\VEN_1106&DEV_0581","viamraid" id = "PCI\VEN_1106&DEV_5324","viamraid" |
|
|
|
|
Oct 22 2006, 06:10 AM
Post
#9
|
|
|
Group: Members Posts: 2 Joined: 22-October 06 Member No.: 113687
|
Nevermind. It is working nicely.
Thanks. |
|
|
|
|
Oct 28 2006, 01:16 AM
Post
#10
|
|
|
Group: Members Posts: 2 Joined: 30-June 05 Member No.: 62469
|
Can't wait to try this on Monday....have a new server build/install giving loads of grief.
[Disks] d1 = "Adaptec SAS RAID Windows 2003 Device Driver", \raidisk1, \ d2 = "Adaptec RAID Windows 2003 Device Driver", \raidisk1, \ [Defaults] scsi = arcsas [Scsi] arcsas = "Adaptec SAS RAID Controller", arcsas arc = "Adaptec RAID Controller", arc [Files.Scsi.arcsas] driver = d1, arcsas.sys, arcsas catalog = d1, arcsas.cat inf = d1, arcsas.inf [Config.arcsas] value = "", Type, REG_DWORD, 1 value = "", Start, REG_DWORD, 0 value = "", Group, REG_SZ, "SCSI miniport" value = "", ErrorControl, REG_DWORD, 1 value = Parameters\Device, NumberOfRequests, REG_DWORD, 0fe [HardwareIds.scsi.arcsas] id = "PCI\VEN_9005&DEV_0285&SUBSYS_02989005", "arcsas" id = "PCI\VEN_9005&DEV_0285&SUBSYS_02f21014", "arcsas" id = "PCI\VEN_9005&DEV_0285&SUBSYS_02999005", "arcsas" id = "PCI\VEN_9005&DEV_0285&SUBSYS_029A9005", "arcsas" id = "PCI\VEN_9005&DEV_0285&SUBSYS_02A49005", "arcsas" id = "PCI\VEN_9005&DEV_0285&SUBSYS_02A59005", "arcsas" id = "PCI\VEN_9005&DEV_0286&SUBSYS_95801014", "arcsas" id = "PCI\VEN_9005&DEV_0286&SUBSYS_95401014", "arcsas" id = "PCI\VEN_9005&DEV_0286&SUBSYS_02A29005", "arcsas" id = "PCI\VEN_9005&DEV_0286&SUBSYS_02A39005", "arcsas" id = "PCI\VEN_9005&DEV_0286&SUBSYS_02AC9005", "arcsas" id = "PCI\VEN_9005&DEV_0286&SUBSYS_02A79005", "arcsas" id = "PCI\VEN_9005&DEV_0286&SUBSYS_02A99005", "arcsas" [Files.Scsi.arc] driver = d2, arc.sys, arc catalog = d2, arc.cat inf = d2, arc.inf [Config.arc] value = "", Type, REG_DWORD, 1 value = "", Start, REG_DWORD, 0 value = "", Group, REG_SZ, "SCSI miniport" value = "", ErrorControl, REG_DWORD, 1 value = Parameters\Device, NumberOfRequests, REG_DWORD, 0fe [HardwareIds.scsi.arc] id = "PCI\VEN_9005&DEV_0285&SUBSYS_02859005", "arc" id = "PCI\VEN_9005&DEV_0285&SUBSYS_02869005", "arc" id = "PCI\VEN_9005&DEV_0285&SUBSYS_02879005", "arc" id = "PCI\VEN_9005&DEV_0285&SUBSYS_028A9005", "arc" id = "PCI\VEN_9005&DEV_0285&SUBSYS_028E9005", "arc" id = "PCI\VEN_9005&DEV_0285&SUBSYS_028B9005", "arc" id = "PCI\VEN_9005&DEV_0285&SUBSYS_028F9005", "arc" id = "PCI\VEN_9005&DEV_0285&SUBSYS_02909005", "arc" id = "PCI\VEN_9005&DEV_0285&SUBSYS_02929005", "arc" id = "PCI\VEN_9005&DEV_0285&SUBSYS_02939005", "arc" id = "PCI\VEN_9005&DEV_0286&SUBSYS_028C9005", "arc" id = "PCI\VEN_9005&DEV_0286&SUBSYS_028D9005", "arc" id = "PCI\VEN_9005&DEV_0285&SUBSYS_3227103C", "arc" id = "PCI\VEN_9005&DEV_0286&SUBSYS_029B9005", "arc" id = "PCI\VEN_9005&DEV_0286&SUBSYS_029C9005", "arc" id = "PCI\VEN_9005&DEV_0286&SUBSYS_029D9005", "arc" id = "PCI\VEN_9005&DEV_0286&SUBSYS_029E9005", "arc" id = "PCI\VEN_9005&DEV_0286&SUBSYS_029F9005", "arc" id = "PCI\VEN_9005&DEV_0286&SUBSYS_02A09005", "arc" id = "PCI\VEN_9005&DEV_0286&SUBSYS_02A19005", "arc" #--The following lines give additional USB floppy support id = "USB\VID_03F0&PID_2001", "usbstor" #--HP id = "USB\VID_054C&PID_002C", "usbstor" #--Sony id = "USB\VID_057B&PID_0001", "usbstor" #--Y-E Data id = "USB\VID_0409&PID_0040", "usbstor" #--NEC id = "USB\VID_0424&PID_0FDC", "usbstor" #--SMSC id = "USB\VID_08BD&PID_1100", "usbstor" #--Iomega |
|
|
|
|
Oct 29 2006, 08:28 AM
Post
#11
|
|
|
Group: Members Posts: 1 Joined: 28-October 06 Member No.: 114240
|
What files go on the disk? Is it Just TXTSETUP.OEM?
|
|
|
|
|
Oct 29 2006, 08:43 PM
Post
#12
|
|
|
Group: Members Posts: 1 Joined: 6-June 05 Member No.: 59299
|
id = "USB\VID_03F0&PID_2001", "usbstor" #--HP
id = "USB\VID_054C&PID_002C", "usbstor" #--Sony id = "USB\VID_057B&PID_0001", "usbstor" #--Y-E Data id = "USB\VID_0409&PID_0040", "usbstor" #--NEC id = "USB\VID_0424&PID_0FDC", "usbstor" #--SMSC id = "USB\VID_08BD&PID_1100", "usbstor" #--Iomega id = "USB\VID_055D&PID_2020", "usbstor" #--Samsung Samsung added to the list... |
|
|
|
|
Oct 31 2006, 06:23 AM
Post
#13
|
|
|
Group: Members Posts: 2 Joined: 30-June 05 Member No.: 62469
|
Spiff,
Thanks. The fix worked great. Server is up and running!! Pete |
|
|
|
 Nov 26 2006, 05:40 PM
Post
#14
|
|
|
Newbie Group: Members Posts: 12 Joined: 16-February 04 Member No.: 14396 |
I found in my usbstor.inf following entries:
[Generic] %GenericBulkOnly.DeviceDesc%=USBSTOR_BULK, USB\Class_08&SubClass_02&Prot_50 %GenericBulkOnly.DeviceDesc%=USBSTOR_BULK, USB\Class_08&SubClass_05&Prot_50 %GenericBulkOnly.DeviceDesc%=USBSTOR_BULK, USB\Class_08&SubClass_06&Prot_50 [Mitsumi] %USB\VID_03EE&PID_0000.DeviceDesc%=USBSTOR_CBI, USB\VID_03EE&PID_0000 %USB\VID_03EE&PID_6901.DeviceDesc%=USBSTOR_CBI, USB\VID_03EE&PID_6901 [HP] %USB\VID_03F0&PID_0107.DeviceDesc%=USBSTOR_BULK, USB\VID_03F0&PID_0107 %USB\VID_03F0&PID_2001.DeviceDesc%=USBSTOR_CBI, USB\VID_03F0&PID_2001 %USB\VID_03F0&PID_4002.DeviceDesc%=USBSTOR_BULK, USB\VID_03F0&PID_4002 %USB\VID_03F0&PID_6102.DeviceDesc%=USBSTOR_BULK, USB\VID_03F0&PID_6102 [NEC] %USB\VID_0409&PID_002C.DeviceDesc%=USBSTOR_BULK, USB\VID_0409&PID_002C %USB\VID_0409&PID_0040.DeviceDesc%=USBSTOR_CBI, USB\VID_0409&PID_0040 [SMSC] %USB\VID_0424&PID_0FDC.DeviceDesc%=USBSTOR_CBI, USB\VID_0424&PID_0FDC [IBM] %USB\VID_04B3&PID_4427.DeviceDesc%=USBSTOR_BULK, USB\VID_04B3&PID_4427 [IOData] %USB\VID_04BB&PID_0301.DeviceDesc%=USBSTOR_CBI, USB\VID_04BB&PID_0301 [FujiFilm] %USB\VID_04CB&PID_0100.DeviceDesc%=USBSTOR_CBI, USB\VID_04CB&PID_0100 [ScanLogic] %USB\VID_04CE&PID_0002.DeviceDesc%=USBSTOR_BULK, USB\VID_04CE&PID_0002 [Panasonic] %USB\VID_04DA&PID_0B01.DeviceDesc%=USBSTOR_CBI, USB\VID_04DA&PID_0B01 %USB\VID_04DA&PID_1B00.DeviceDesc%=USBSTOR_CB, USB\VID_04DA&PID_1B00 %USB\VID_04DA&PID_0B03.DeviceDesc%=USBSTOR_BULK, USB\VID_04DA&PID_0B03 [SCM] %USB\VID_04E6&PID_0001.DeviceDesc%=USBSTOR_CB, USB\VID_04E6&PID_0001 %USB\VID_04E6&PID_0002.DeviceDesc%=USBSTOR_BULK, USB\VID_04E6&PID_0002 %USB\VID_04E6&PID_000A.DeviceDesc%=USBSTOR_BULK, USB\VID_04E6&PID_000A %USB\VID_04E6&PID_0101.DeviceDesc%=USBSTOR_BULK, USB\VID_04E6&PID_0101 [Sony] %USB\VID_054C&PID_0022.DeviceDesc%=USBSTOR_BULK, USB\VID_054C&PID_0022 %USB\VID_054C&PID_0023.DeviceDesc%=USBSTOR_CB, USB\VID_054C&PID_0023 %USB\VID_054C&PID_0024.DeviceDesc%=USBSTOR_CB, USB\VID_054C&PID_0024 %USB\VID_054C&PID_0025.DeviceDesc%=USBSTOR_CB, USB\VID_054C&PID_0025 %USB\VID_054C&PID_002C.DeviceDesc%=USBSTOR_CBI, USB\VID_054C&PID_002C %USB\VID_054C&PID_0032.DeviceDesc%=USBSTOR_CBI_NR, USB\VID_054C&PID_0032 %USB\VID_054C&PID_0037.DeviceDesc%=USBSTOR_CBI, USB\VID_054C&PID_0037 %USB\VID_054C&PID_0046.DeviceDesc%=USBSTOR_CBI, USB\VID_054C&PID_0046 %USB\VID_054C&PID_004A.DeviceDesc%=USBSTOR_CBI, USB\VID_054C&PID_004A %USB\VID_054C&PID_0056.DeviceDesc%=USBSTOR_CBI_NR, USB\VID_054C&PID_0056 %USB\VID_054C&PID_0058.DeviceDesc%=USBSTOR_CBI, USB\VID_054C&PID_0058 %USB\VID_054C&PID_0069.DeviceDesc%=USBSTOR_CBI_NR, USB\VID_054C&PID_0069 [YEData] %USB\VID_057B&PID_0000.DeviceDesc%=USBSTOR_CBI, USB\VID_057B&PID_0000 %USB\VID_057B&PID_0001.DeviceDesc%=USBSTOR_CBI, USB\VID_057B&PID_0001 %USB\VID_057B&PID_0010.DeviceDesc%=USBSTOR_BULK, USB\VID_057B&PID_0010 [Iomega] %USB\VID_059B&PID_0001.DeviceDesc%=USBSTOR_BULK, USB\VID_059B&PID_0001 %USB\VID_059B&PID_0030.DeviceDesc%=USBSTOR_BULK, USB\VID_059B&PID_0030 %USB\VID_059B&PID_0031.DeviceDesc%=USBSTOR_BULK, USB\VID_059B&PID_0031 %USB\VID_059B&PID_0032.DeviceDesc%=USBSTOR_BULK, USB\VID_059B&PID_0032 %USB\VID_059B&PID_0060.DeviceDesc%=USBSTOR_BULK, USB\VID_059B&PID_0060 [LaCie] %USB\VID_059F&PID_A601.DeviceDesc%=USBSTOR_CB, USB\VID_059F&PID_A601 %USB\VID_059F&PID_A602.DeviceDesc%=USBSTOR_CB, USB\VID_059F&PID_A602 [TEAC] %USB\VID_0644&PID_0000.DeviceDesc%=USBSTOR_CBI, USB\VID_0644&PID_0000 %USB\VID_0644&PID_1000.DeviceDesc%=USBSTOR_BULK, USB\VID_0644&PID_1000 [Hagiwara] %USB\VID_0693&PID_0002.DeviceDesc%=USBSTOR_BULK, USB\VID_0693&PID_0002 %USB\VID_0693&PID_0003.DeviceDesc%=USBSTOR_BULK, USB\VID_0693&PID_0003 %USB\VID_0693&PID_0005.DeviceDesc%=USBSTOR_BULK, USB\VID_0693&PID_0005 %USB\VID_0693&PID_0006.DeviceDesc%=USBSTOR_BULK, USB\VID_0693&PID_0006 %USB\VID_0693&PID_0007&MI_00.DeviceDesc%=USBSTOR_BULK, USB\VID_0693&PID_0007&MI_00 %USB\VID_0693&PID_000A.DeviceDesc%=USBSTOR_BULK, USB\VID_0693&PID_000A [Imation] %USB\VID_0718&PID_0002.DeviceDesc%=USBSTOR_BULK, USB\VID_0718&PID_0002 %USB\VID_0718&PID_0003&MI_00.DeviceDesc%=USBSTOR_BULK, USB\VID_0718&PID_0003&MI_00 [SanDisk] %USB\VID_0781&PID_0001.DeviceDesc%=USBSTOR_CB, USB\VID_0781&PID_0001 %USB\VID_0781&PID_0002&MI_00.DeviceDesc%=USBSTOR_BULK, USB\VID_0781&PID_0002&MI_00 %USB\VID_0781&PID_0100.DeviceDesc%=USBSTOR_CB, USB\VID_0781&PID_0100 [Casio] %USB\VID_07CF&PID_1001.DeviceDesc%=QV2KUX, USB\VID_07CF&PID_1001 [DioGraphy] %USB\VID_0892&PID_0101.DeviceDesc%=USBSTOR_BULK, USB\VID_0892&PID_0101 [M-Sys] %USB\VID_08EC&PID_0010.DeviceDesc%=USBSTOR_BULK, USB\VID_08EC&PID_0010 [Addonics] %USB\VID_0BF6&PID_1234.DeviceDesc%=USBSTOR_BULK, USB\VID_0BF6&PID_1234 %USB\VID_0BF6&PID_0103.DeviceDesc%=USBSTOR_BULK, USB\VID_0BF6&PID_0103 [OnSpec] %USB\VID_55AA&PID_0102.DeviceDesc%=USBSTOR_BULK, USB\VID_55AA&PID_0102 %USB\VID_55AA&PID_0103.DeviceDesc%=USBSTOR_BULK, USB\VID_55AA&PID_0103 %USB\VID_55AA&PID_1234.DeviceDesc%=USBSTOR_BULK, USB\VID_55AA&PID_1234 %USB\VID_55AA&PID_B004.DeviceDesc%=USBSTOR_BULK, USB\VID_55AA&PID_B004 %USB\VID_55AA&PID_B200&MI_00.DeviceDesc%=USBSTOR_BULK, USB\VID_55AA&PID_B200&MI_00 %USB\VID_55AA&PID_B204&MI_00.DeviceDesc%=USBSTOR_BULK, USB\VID_55AA&PID_B204&MI_00 %USB\VID_55AA&PID_B207&MI_00.DeviceDesc%=USBSTOR_BULK, USB\VID_55AA&PID_B207&MI_00 Is this possible to add this also in txtsetup.sif and/or dosnet.inf if needed? Example: Add following lines under section: [HardwareIdsDatabase] ... I don't know the correct syntax to implement this, maybe someone else has better knowledge to add those extra usb-floppy devices? Greets from Belgium! This post has been edited by Cobravox: Nov 26 2006, 05:52 PM
Attached File(s)
|
|
|
|
 Jan 19 2007, 04:47 AM
Post
#15
|
|
|
Group: Members Posts: 2 Joined: 21-July 06 Member No.: 105247
|
Hi guys, I tried this solution with a USB KEY and it doesn't work at all ! It's weird because the USB KEY use exactly the same principle. 1) - Get the USB\VID adress : With Devcon I list all the " hardware ID's of devices. " with the command line : Devcon /hwids * > OUT.TXT #-----------------------------------------------------# USB\VID_0930&PID_6540F8125605192D91E Name: USB Mass Storage Device Hardware ID's: USB\Vid_0930&Pid_6540&Rev_0200 USB\Vid_0930&Pid_6540 #-----------------------------------------------------# 2) - Add the new ID within the " txtsetup.oem " #--The following lines give additional USB floppy support id = "USB\VID_03F0&PID_2001", "usbstor" #--HP id = "USB\VID_054C&PID_002C", "usbstor" #--Sony id = "USB\VID_057B&PID_0001", "usbstor" #--Y-E Data id = "USB\VID_0409&PID_0040", "usbstor" #--NEC id = "USB\VID_0424&PID_0FDC", "usbstor" #--SMSC id = "USB\VID_08BD&PID_1100", "usbstor" #--Iomega id = "USB\VID_055D&PID_2020", "usbstor" #--Samsung id = "USB\Vid_0930&Pid_6540", "usbstor" #--MY USB KEY * 3) - Go to the BIOS configuration and enable the floppy emulation over the USB KEY On theory everything is fine, except the fact that it doesn't work  , any ideas ? |