i have made a usb stick bootable with diskpart but i still can start my winpe 2.0 i get the error
file : /boot/bcd
status
0xc000000e
i search the net but i cant find what i do wrong can somebody help me pleas.
Full Version: WindowsPE 2.0 need help.
QUOTE (yucatan @ Jun 28 2008, 07:27 AM) 
i have made a usb stick bootable with diskpart but i still can start my winpe 2.0 i get the error
file : /boot/bcd
status
0xc000000e
i search the net but i cant find what i do wrong can somebody help me pleas.
i used different guides all no working... why i just dont understand pleas help me
file : /boot/bcd
status
0xc000000e
i search the net but i cant find what i do wrong can somebody help me pleas.
i used different guides all no working... why i just dont understand pleas help me
Did you do this?
This must be done from Windows Vista.
Start a command prompt and run the following. This set of commands assumes your USB key is detected as disk 1, you should double check that by doing a list of the disks before cleaning it. If you have multiple hard drives you could end up wiping your second drive using this command. You have been warned.
• Diskpart
• select disk 1
• clean
• create partition primary
• select partition 1
• active
• format fs=NTFS
• assign
• exit
Then just copy All files WinPE CD to the USB Key
This must be done from Windows Vista.
Start a command prompt and run the following. This set of commands assumes your USB key is detected as disk 1, you should double check that by doing a list of the disks before cleaning it. If you have multiple hard drives you could end up wiping your second drive using this command. You have been warned.
• Diskpart
• select disk 1
• clean
• create partition primary
• select partition 1
• active
• format fs=NTFS
• assign
• exit
Then just copy All files WinPE CD to the USB Key
QUOTE (FredBeagle @ Jun 28 2008, 03:41 PM)
Did you do this?
This must be done from Windows Vista.
Start a command prompt and run the following. This set of commands assumes your USB key is detected as disk 1, you should double check that by doing a list of the disks before cleaning it. If you have multiple hard drives you could end up wiping your second drive using this command. You have been warned.
• Diskpart
• select disk 1
• clean
• create partition primary
• select partition 1
• active
• format fs=NTFS
• assign
• exit
Then just copy All files WinPE CD to the USB Key
This must be done from Windows Vista.
Start a command prompt and run the following. This set of commands assumes your USB key is detected as disk 1, you should double check that by doing a list of the disks before cleaning it. If you have multiple hard drives you could end up wiping your second drive using this command. You have been warned.
• Diskpart
• select disk 1
• clean
• create partition primary
• select partition 1
• active
• format fs=NTFS
• assign
• exit
Then just copy All files WinPE CD to the USB Key
yea i did that on my usb key and i did copy the files but i get the error 0xc000000e
file /boot/bcd
I have used these steps over 100 time with sucess, it might me your hardware.
What is the PC that you are using?
What kind of USB drive?
If you burn your bulid to a CD/DVD will it boot?
What is the PC that you are using?
What kind of USB drive?
If you burn your bulid to a CD/DVD will it boot?
QUOTE (FredBeagle @ Jun 30 2008, 07:59 PM)
I have used these steps over 100 time with sucess, it might me your hardware.
What is the PC that you are using?
What kind of USB drive?
If you burn your bulid to a CD/DVD will it boot?
What is the PC that you are using?
What kind of USB drive?
If you burn your bulid to a CD/DVD will it boot?
i could burn it so i could test
i tryed on different machines.
all same error.
QUOTE (yucatan @ Jul 2 2008, 12:09 PM)
QUOTE (FredBeagle @ Jun 30 2008, 07:59 PM)
I have used these steps over 100 time with sucess, it might me your hardware.
What is the PC that you are using?
What kind of USB drive?
If you burn your bulid to a CD/DVD will it boot?
What is the PC that you are using?
What kind of USB drive?
If you burn your bulid to a CD/DVD will it boot?
i could burn it so i could test
i tryed on different machines.
all same error.
Hi
Try it on a different mainboard. Some mainboards give this error but most other mainboards boot fine from the same USB drive. On one mainboard D915GUX, I can boot a USB CD drive WinPE image, but cannot boot the same image when using a USB flash memory stick - but the same stick does boot on every other mainboard I have!
This is a "lo-fi" version of our main content. To view the full version with more information, formatting and images, please click here.