onepic

Member
  • Content count

    5
  • Joined

  • Last visited

Community Reputation

0 Neutral

About onepic

  1. I finaly get a Nokia CA-42 cable managed to put the drive (Seagate 7200.11 SD15 - 1TB) in diagnostic mode but when i input the command: m0,2,2,0,0,0,0,22 nothing happend ... Here is the log: Rst 0x20M ASCII Diag mode F3 T>/2 F3 2>Z Spin Down Complete Elapsed Time 0.127 msecs F3 2>U Spin Up Complete Elapsed Time 6.814 secs F3 2>/ F3 T>F712 Byte:05A1: Expansion = 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 '' F3 T>F,,22 Drive Configuration restored to defaults. RAW OFF RWSWD-OptChange: Ctrl 0001 Dvgas 0008 Rvgas 0008 Fvgas 0008 SumOf 0008 WriteCapInfo Selection = 0000 CurrentCap 00000000 HDACap 74706DB0 Update Cap and Save CurrentHDA 74706DB0 HDACap 74706DB0 NativeCap 74706DB0 48BitCap 74706DB0 28BitCa p 0FFFFFFF SaveCapInfo (P) SATA Reset PASSPackage Verified F3 T>F712 Byte:05A1: Expansion = 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 '' F3 T>/1 F3 1>N1 F3 1>/ F3 T>m0,2,2,0,0,0,0,22 ---> w8 about 20 min. but nothing happend Or after i input N1 i power OFF the drive and then ON after 10 seconds (by unplug and plug back the SATA power cable) and press ctrl+z i get F3 1> and when i try to input the commands like F,,22 or m0,2,2,0,0,0,0,22 is not working. What i do wrong ? Please help because i'm desperate ! PS. I have try on Windows 7 (putty) and on Windows XP (hyperterminal) and the same. ================================== Managed to make it work without GND from CA-42 connected but i get this: F3 T>m0,2,2,0,0,0,0,22 Max Wr Retries = 00, Max Rd Retries = 00, Max ECC T-Level = 00, Max Certify Rewr ite Retries = 0000 User Partition Format 3% complete, Zone 00, Pass 00, LBA 00004AA5, ErrCode 000 00080, Elapsed Time 0 mins 30 secs User Partition Format Successful - Elapsed Time 0 mins 30 secs Zone re-format was skipped. F3 T> and the drive is not show in BIOS. It is damaged ?
  2. I have finally make the interface working but when i start the terminal and power up the drive only Rst 0x20M and after i press Ctrl+Z nothing happen ... What it can be wrong ?
  3. Hi there, My Seagate 1TB drive model SR31000333AS with firmware SD15 has just died inside a iOmega external HDD. I have open the cover of iOmega and only after that i was see the model and firmware . The drive it seems to be in BSY state and it is not recognized into the BIOS. I was get a NKI 6100 data cable with COM port and identified the pins as Black = Tx, Green = GND and Red = Rx. The adapter is like into this picture: The problem is i can't get after i press Ctrl+z into the terminal the F3 T> prompt. I have changed the Rx with Tx but the same. So anyone it recognize the board into the picture above and can confirm i have identified correct the wires ? Thank you !
  4. I have renamed unattended.txt into unattended.tx_ and i have rebuild the setup and now all ok and it run like from original CD. Th'x for the tip ! btw... tested today on a 16GB usb stick and is working OK from there too.
  5. @ilko_t Nice work and pls. receive my congratulations for it ! I have test it today and it is working OK from a 2GB USB Stick (formated as NTFS) and installed from it a winxp sp3 profesional VLK on my notebook but there is "small problem". The setup it seems not ask to select your Name and Organization and also skip the selection for time zone . Can you fix that because not all of us are live in US . Thank you in advance !