Jump to content

kang roy

Member
  • Posts

    15
  • Joined

  • Last visited

  • Donations

    0.00 USD 
  • Country

    Indonesia

About kang roy

Contact Methods

  • Yahoo
    roy.rohadi

kang roy's Achievements

0

Reputation

  1. I have no idea whether this is now known here, Model : ST1000DM003 S/N : W1D0LXS2 P/N : 9YN162-303 Fw : CC4D Date :12344 Stite : WU I managed to connect to the disk's serial interface, and this is the diagnostic output it gives upon power-up. Hopefully someone qualified can step up and tell us what it actually is that the ST1000DM003s are choking on . Boot 0x40M Spin Up[0x000065B4][0x00006A20][0x00006E8C] Trans. Rst 0x40M MC Internal LPC Process Spin Up (P) SATA Reset MCMainPOR: Start: Check MCMT Version: Current MCMainPOR: Non-Init Case MC Seg Disc and Cache Nodes: 40125B20 40122EF8 Seg Write Preamble VBM start: 0000204A end: 00002091 Footer - start: 00002093 end: 000020DA Seg Read Preamble VBM - start: 000020DC end: 00002123 Footer - start: 00002125 end: 0000216C Reconstruction: MCMT Reconstruction Start Max number of MC segments 0A61 Nonvolatile MCMT sequence number 0038E0B8 [RSRS] 0729 ProcessRWError -Read- at LBA 000000000005CA36 Sense Code=40000087 InitiateMarkPendingReallocateRequest for disc_lba: 000000000005CA36! Reconstruction: EXCEPTION: Seg Read Fail: Status = 0000 Continuing after error ReadFooters (Forward): Segment 0729 StartLBA 00000000002E5138 Starting Footer LBA 00000000002E5180 SeqNum 0038E0B9 TotalUserBlocks 0000 ProcessRWError -Read- at LBA 000000000005CA36 Sense Code=40000087 InitiateMarkPendingReallocateRequest for disc_lba: 000000000005CA36! Footer Status = 0000 Footer Status = 0001 Footer Status = 0001 Footer Status = 0001 Footer Status = 0001 Footer Status = 0001 Footer Status = 0001 Footer Status = 0001 Footer Status = 0001 Footer Status = 0001 Footer Status = 0001 Footer Status = 0001 Footer Status = 0001 Footer Status = 0001 Footer Status = 0001 Footer Status = 0001 Footer Status = 0001 Footer Status = 0001 Footer Status = 0001 Footer Status = 0001 Footer Status = 0001 Footer Status = 0001 Reconstruction: EXCEPTION: Segment Overall Sequence Number Mismatch, No Valid Footer 0038E0B9 AABBAAAA Reconstruction: ProcessIncompletelyWrittenSegment
  2. Test : Reset S.M.A.R.T SMART erase... Reset S.M.A.R.T................................... : Error Drive not ready Rst 0x20M (P) SATA Reset PASS RW: Error processing Performance Parameter File: 203C Send Status: COMRESET seen InitiateMarkPendingReallocateRequest for disc_lba: 00000067
  3. how to overcome the problem segate Barracuda 7200.10 friends may know how ? Interface task reset 1024k x 16 SDRAM TONKA2 - 1_Disk M-31 03-22-06 10:53 Head Mask FFFF - Switch to full int. Spin Ready (P)PATA Reset Not Interface Age! INVALID Cert Disk Code - ROM Resident Revision Required: AAJ4T0 Command Inactive - No VALID Cert Code Detected T>
  4. hello I have a SCSI hard drive capacity deteck not, I want to ask for help can help me to overcome something like this?
  5. the drive is WD mypassport 320 GB and it works perfectly on my laptop, But my desktop computer can not access it. The device is shown in both explorer and device manager but not shown in disk managment consul. same issue with checkdisk. What solutions?
  6. i'm sorry.... to overcome problems such as WDC is not detected in the BIOS, the sound head and Short PCBs, probably from among you have a solution,,, help please,,, with a tutorial,,,
  7. it might not install correctly, try your ripaire
  8. to cope with problems such as the WDC is not detected in bios, sound and fire its board, probably from among you have a solution,,, help please,,, by following the tutorial,,,
  9. there are some troubled hdd like this, it is likely that problems with its own hdd, such as bad sectors, and also fit in time to copy the files may copy files bad sector, the way this work should be cloned into an empty hdd,, , has completed a new clone in its use of data recovery software that tough if you can use forensic software,,,
  10. sorry, his views of the scenario you have installed the operating system while the files you are connected to the drive C, you are using recovery software? let you use the software R-studio recovery
  11. Could mean another way / underdos flash back / comennt dos, Whether it be by way coment? please explain in the tutorial.
  12. Now wait 15~30 seconds until something like this appears (it will vary a bit): Max Wr Retries = 00, Max Rd Retries = 00, Max ECC T-Level = 00, Max Certify Rewrite Retries = 0000 User Partition Format 5% complete, Zone 00, Pass 00, LBA 00008DED, ErrCode 00000080, Elapsed Time 0 mins 05 secs User Partition Format Successful - Elapsed Time 0 mins 05 secs ONLY after the message like above you can turn off everything. Fixing BSY or CC errors aka BUSY (I recommend some practice before trying this): Note: All commands are case sensitive ! First, make sure you have your hard drive accessible; on a table with open access to the drive is best. Second, you need to remove the PCB (Printed Circuit Board) from HDA case using a Mini Torx 6 screw driver. Third, connect RX & TX cables from your RS-232 adapter, verify that all is correct, and then connect the power supply to Hard drive circuit board. Explanation: The problem with the drive is that the drive is stuck/halt in a BUSY state. This basically locks up the SATA port, causing the BIOS problem (cannot detect the drive at POST). In the terminal, you will see this sort of error (LED: 000000CC FAddr: 0024A051). Once you see this in the terminal, the terminal session to the drive is completely blocked and will not accept any more commands. In order to circumvent this, we'll need to disconnect the PCB (circuit board) from the hard drive case so that the LED: 000000CC FAddr: 0024A051 command cannot be sent from the firmware of the terminal session. After you have connected the power to the circuit board, press CTRL+Z in your HyperTerminal session. You should now see a prompt like this: F3 T> If you do not see this prompt, check your RS-232 connections to the drive. (you may have the TX and RX flipped). Now we'll need to access the Level 2, type: F3 T>/2 (enter) F3 2> And type (to spind down the motor): F3 2>Z (enter) Spin Down Complete Elapsed Time 0.147 msecs (the time will vary here) F3 2> Now the tricky part. Pratice a lot without any power before even trying this. You need to make sure that the screws don't touch the PCB board where they aren't suppose to or you will fry your PCB board. If you have been practicing and the power is not connected, start at STEP ONE. With the POWER CONNECTED to the PCB board, as well as your TX/RX terminal wires, mount the board back on the HDA case. You must have the power connected when you do this. Now type (to start the motor): F3 2>U (enter) You should get something like this: Spin Up Complete Elapsed Time 7.093 secs F3 2> Then go to Level 1 (by typing /1): F3 2>/1 (enter) Now lets do a S.M.A.R.T. erase (create S.M.A.R.T. sector): F3 1>N1 (enter) ------------------------------------------------------------------------------------- G-List step is optional: Skip G-List step first, if after proceeding the whole BSY fix and the drive still remains under BSY error, then you'll need to repeat BSY process with G-List command below. G-List Erase (Fix Defect List): F3 1>/T (enter) F3 T>i4,1,22 (enter) For reference: ------------------------------------------------------------------------------------- Power OFF/ON the drive (very important!) Wait 10 seconds and now Power ON your drive. Press CTRL+Z on terminal and type: Partition regeneration: F3 T>m0,2,2,,,,,22 (enter) For reference: You should get something like (in around 15~30 seconds): Max Wr Retries = 00, Max Rd Retries = 00, Max ECC T-Level = 14, Max Certify Rewrite Retries = 00C8 User Partition Format 10% complete, Zone 00, Pass 00, LBA 00004339, ErrCode 00000080, Elapsed Time 0 mins 05 secs User Partition Format Successful - Elapsed Time 0 mins 05 secs If you didn't get the msg above, then you skipped something important, and turning off your drive now will render an unreadable drive, so be careful. ONLY after the message like above you can turn off everything. A direct guide for BSY error (with photos): http://www.msfn.org/board/index.php?showto...8807&st=100 Keep in mind I did my best to compile all this information and provide more and better details. Gradius Could this way to restore the data again arriving in the hdd?
  13. type SCSI seagate Cheetah Ultra 320 (ST336607LC) MAde in singapore I want the tutorial to mengembelikan scsi HDD capacity is, if you can help me?
  14. Please keep in mind that with SCSI drives out of 100 cases, 98 99 are solved by checking the connections, a bad SCSI cable or a mis-terminated bus is a very, very common issue. I have carefully examined the connection, but the result is zero, I've used other scsi hdd running smoothly,,, Can you explain how to restore the capacity scsi hd right?
  15. I have a scsi hardrive, but to detect its 0 byte, if there is a solution for this?
×
×
  • Create New...