• Content count

  • Joined

  • Last visited

Community Reputation

0 Neutral

About Littlebr00k

  • Rank
    Out there, somewhere!

Contact Methods

  • Website URL
  1. There are a few ways to do it, but the best I found for cross browser support is available here. Hope this helps.
  2. Thank you for the appreciation! But, Plants is already uploaded! Have you got a problem downloading it? For Wet Shadows, I opened it in XPreview and was displayed fine (see the shot below). However, XPreview displays files at low resolution (not 1024x768). This is why I use WINNTBBU Editor to display the file at 1024x768 which the file is designed for. I also recieve errors when trying to open in XPreview And in WINNTBBU Editor I tried renaming and it doesn't work either. Could it be a problem with the downloaded version versus the original on your computer? There isn't a problem with the file it just seems as if WinntbbuED has a problem expanding it. If you open a command prompt in the directory you downloaded it and type expand -r Wet_Shadows_by_maxxin.dl_ and then hit enter or return, WINNTBBU.DLL will be expanded into the same directory. You will then be able to view it WinntbbuED or XPreview. Hope this helps.
  3. I had this happen to me a while back and finally traced the problem to the CPU. Try removing it and cleaning out any dirt and replacing it. If not change the CPU for another one and you will find the PC will boot.
  4. are you this is the right link? It should be
  5. You could see if its possible to change the hotkey in maple to something else or you could use something like AutoHotkey to remap your current hotkey configuration on windows.
  6. With the error of the cpu not being recognized correctly and it asking you to enter the bios, it sounds as if the the cmos battery is failing and cannot keep the info when the power is off. These are cheap and easy to replace and available from electronic shops, computer shops etc. Make sure you get the right one, perhaps take the old one with you. It could also be that you have a dust build up inside the case. Open it up and clean it out, while you have it open it may be beneficial to remove and reseat every card attached to the mobo in case you have a dirty connection on one of them. Also clean the heatsink and fan on the cpu and ensure it is on correctly incase you have a heat build up and the cooling isn't doing its job.
  7. TI7.0 has been given away free on a few computer mags, check your local store you may still be able to find one. When you create the backup partion you are given the option of password protecting the contents. This only stops the user from changing the contents, and the password needs to be supplied when restoring from this backup. It doesn't stop the partion from being deleted or viewed through the computer management console.
  8. I used to run into a few problems developing on PWS, it is not a fully featured web server. There are a few free web servers out there most noteably Abyss Web Server which has a very small download and installed footprint. Go here for easy to follow instructions to configure Abyss to run with perl and other technologies. Abyss is so easy to install and configure, I know a few companies that are using it in production enviroments. Hope this helps.
  9. Under Logical Disk Management, is you raid set as active? Also not knowing what raid chip you are using, can you go into the raid configuration screen / bios and check that it is set to first boot device / active in there. If these are set correctly then I can only think that the Master Boot Record is corrupt on the raid and needs replacing. First check the boot paths by Edit your c:\boot.ini file. The easiest way is usually with msconfig. Start/Run/msconfig <enter>. Click on the Boot.ini tab. Click on Check all boot paths. should look something like [boot loader] timeout=5 default=multi(0)disk(0)rdisk(0)partition(1)\WINDOWS [operating systems] multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Microsoft Windows XP Professional" /noexecute=optin /fastdetect may be slightly different due to the raid but there should be no mention of a cd drive or Boot you pc to the recovery console and at the command prompt type FIXMBR and hit return and reboot without the CD. or Use an old Win98 boot disk at the command promp type fdisk /mbr to replace the mbr, then type fdisk /status which will show you you the current status of your disks and whether they are bootable and active. Hope this helps.
  10. There a few things we need to do to enable asp in iis. 1) open Internet Information Services (IIS) Manager 2) expand the tree on the left until you find Default Web Site or whatever you named yours 3) right click on the entry and select properties 4) Select the Home Directory tab and tick Read, Write, Log Visits, Index This Resource 5) On the Home Directory tab change the Execute Permissions to Scripts and Executables and accept the prompt. 6) Select the Configuration button and select the Options tab, Tick Enable Parent Paths and change the Default ASP Language to whatever you are using. Click on OK and then apply in thmain window. 7) If you get any Inheritence Override Windows, Click the Select All button followed by OK. 8) Select the Documents tab, and ensure you have Default.asp and Index.asp in the list, if not add them 9) Click on APPLY and OK IIS will now serve asp pages. You may have to restart IIS, but you shouldn't need to. Hope this helps
  11. Have you changed your bios to boot from the raid as the first device?
  12. A bit more info would help diagnose the problem 1) what browser are you using 2) what firewall do you use 3) how do you connect to the internet 4) give an example of a site you can't connect to
  13. If html pages load then what extension of web page are you trying to load (eg asp, php, aspx)?
  14. The product key is still in the registry but it i encoded different ways in different places. If you are programming in delphi Go Here If you are programming in C# Go Here Hope this helps
  15. Why didn't I think about uploading it? /crawls under desk and hides