Gradius2

The Solution for Seagate 7200.11 HDDs

4,868 posts in this topic

Hi people,

i'm also trying to unbrick my seagate but at the moment when i power on my harddrive some moments later hyperterminal and windows xp freezes.

Can somebody help me ?

0

Share this post


Link to post
Share on other sites

Hi people,

i'm also trying to unbrick my seagate but at the moment when i power on my harddrive some moments later hyperterminal and windows xp freezes.

Can somebody help me ?

I do hope your SATA data cable is not connected? :ph34r: Otherwise give more info of exactly what you are trying to commit there, since I normally leave my crystal ball at work and do not have access to it during weekends.

0

Share this post


Link to post
Share on other sites

I've got the setup of this guy (http://www.mapleleafmountain.com/seagatebrick.html) and i get just till the moment that i have to power on my sata drive. Sata data cable not attached

Thanks for having a look at this.

Dirk

Hi people,

i'm also trying to unbrick my seagate but at the moment when i power on my harddrive some moments later hyperterminal and windows xp freezes.

Can somebody help me ?

I do hope your SATA data cable is not connected? :ph34r: Otherwise give more info of exactly what you are trying to commit there, since I normally leave my crystal ball at work and do not have access to it during weekends.

0

Share this post


Link to post
Share on other sites

That is the right guide to use :)

Does your loopback test work? Do you have a cheap PSU? See here.

Otherwise we need more info on your converter setup and everything in your own words. The more detail you give, the more likely we will be able to identify the problem.

0

Share this post


Link to post
Share on other sites

Hi,

I have a Seagate 7200.11 barracuda 500GB.. The hard disc went kaput yesterday.. The problem I have is that the hard disc was my booting disc and in order to proceed with any of the Data recovery methods suggested, i need to have windows xp installed.. so my question is do I purchase a new hard drive and install xp on it.. if i do so won't the bricked seagate drive conflict with the new hard disc's OS when trying the data recovery method?

Thanks in advance! :)

0

Share this post


Link to post
Share on other sites

I have a Seagate 7200.11 barracuda 500GB.. The hard disc went kaput yesterday.. The problem I have is that the hard disc was my booting disc and in order to proceed with any of the Data recovery methods suggested, i need to have windows xp installed.. so my question is do I purchase a new hard drive and install xp on it..

Maybe phone a friend...

Otherwise, yes.

if i do so won't the bricked seagate drive conflict with the new hard disc's OS when trying the data recovery method?

No, data cable not connected during fix. :)

Edited by BlouBul
0

Share this post


Link to post
Share on other sites

I fixed my drive tonite. Thanks for your advice about the PSU. I tried with a 300W causing Windows and Hyperterminal to freeze when powering up the Barracuda. Switching to a 450W PSU pulled the trick.

2 notes :

i have firmware SD25

i followed this excellent tutorial http://www.mapleleafmountain.com/seagatebrick.html but before regenerating the partitions pull out the sata power cable and wait 1 minute (not doing so caused a very long wait and nothing happened)

Thanks BlouBul you made my day.

That is the right guide to use :)

Does your loopback test work? Do you have a cheap PSU? See here.

Otherwise we need more info on your converter setup and everything in your own words. The more detail you give, the more likely we will be able to identify the problem.

0

Share this post


Link to post
Share on other sites

I fixed my drive tonite. Thanks for your advice about the PSU. I tried with a 300W causing Windows and Hyperterminal to freeze when powering up the Barracuda. Switching to a 450W PSU pulled the trick.

Thanks BlouBul you made my day.

Glad it worked :thumbup (and you're welcome :D )

0

Share this post


Link to post
Share on other sites

I fixed my drive tonite. Thanks for your advice about the PSU. I tried with a 300W causing Windows and Hyperterminal to freeze when powering up the Barracuda. Switching to a 450W PSU pulled the trick.

2 notes :

i have firmware SD25

i followed this excellent tutorial http://www.mapleleafmountain.com/seagatebrick.html but before regenerating the partitions pull out the sata power cable and wait 1 minute (not doing so caused a very long wait and nothing happened)

Thanks BlouBul you made my day.

That is the right guide to use :)

Does your loopback test work? Do you have a cheap PSU? See here.

Otherwise we need more info on your converter setup and everything in your own words. The more detail you give, the more likely we will be able to identify the problem.

About firmware you can use SD1A in place of SD25. I used it! It works fine.

0

Share this post


Link to post
Share on other sites

I have finally make the interface working but when i start the terminal and power up the drive only

Rst 0x20M

and after i press Ctrl+Z nothing happen :(... What it can be wrong ?

Edited by onepic
0

Share this post


Link to post
Share on other sites

and after i press Ctrl+Z nothing happen :(... What it can be wrong ?

Please read FGA. Pay special attention to #4 :whistle:

Edited by BlouBul
0

Share this post


Link to post
Share on other sites

I have a bricked Segate Barracuda 7200.11 750GB

I read a couple guides and FAQ sticky, http://440beb44.qvvo.com/

I have a problem I did not see anyone mention

except that you get this message if I hit ctrl-z too soon

I Type ctrl+z

F3 T>

I Type /2

F3 2>

I Type Z and press enter

LED:000000CE FAddr:0025A261

LED:000000CE FAddr:0025A261

LED:000000CE FAddr:0025A261

i don't get "Spin Down Complete, Elapsed Time 0.146 msecs"

and yes I have the PCB disconnected using a card

UPDATE:

I just tried it by removing the pcb completely and now it worked.

so putting the card in to disconnecting is not a good idea.

Thanks for the fix!

hope my data is there, still working on it at this time.

Edited by Fireflynj
0

Share this post


Link to post
Share on other sites

I read a couple guides and FAQ sticky,

This the FAQ sticky, I guess you are talking about the FGA http://homepage.ntlworld.com./jonathan.deboynepollard/FGA/fga-not-faq.html

I read a couple guides and FAQ sticky, http://440beb44.qvvo.com/

I have a problem I did not see anyone mention

except that you get this message if I hit ctrl-z too soon

I Type Z and press enter

LED:000000CE FAddr:0025A261

LED:000000CE FAddr:0025A261

LED:000000CE FAddr:0025A261

i don't get "Spin Down Complete, Elapsed Time 0.146 msecs"

and yes I have the PCB disconnected using a card

Did you read the recommended guide by CarterinCanada? :whistle:

Note: Some guides on the web have suggested insulating the *other* set of contacts (the "head" contacts) you see in the lower left of the above photo to the right. I tried this originally and it didn't work for me but obviously others have had some success with it. In *my* case, with 1TB model drives, I can assure you that insulating the slightly easier to access motor contacts worked where the head contacts method didn't. I suspect the specific model of your drive will account for the varying levels of the results so if one way doesn't work for you, think about trying the other. You'll know to look here if the HyperTerminal session won't allow you to spin down the drive and continues to give you the BSY error in reply - "LED:01...blah blah blah". If you're allowed to spin down the drive, then this bit isn't your issue.

UPDATE:

I just tried it by removing the pcb completely and now it worked.

so putting the card in to disconnecting is not a good idea.

Thanks for the fix!

hope my data is there, still working on it at this time.

That is the more difficult way (to put the whole pcb back with power on :ph34r: ), but glad it worked :)

0

Share this post


Link to post
Share on other sites

Hello again digital warriors!

Carter here just checking in with ongoing firmware war. You lot are doing fine work as usual getting the digital masses back to working order. Your computer karma should be off the charts by now.

I wanted to chime in with a little tidbit I’ve just updated on my method. I got a nice email from an engineer at Pololu, the company that makes the adapter I used to unbrick my own drives, informing me of a something they’ve started to see in the field now that there are hundreds (if not thousands) of you out there on the path to drive redemption. It seems that if you use particularly long jumpers in your setup, some LC voltage spikes can crop up and cause permanent damage to your adapter and cause you temporary insanity trying to sort out what went wrong. They have been able to reproduce the ‘effect’ consistently with jumper wires at 3 feet (about a meter) long. On their site they have linked a paper on the topic ( http://www.pololu.com/docs/0J16 ) for any of you tech nerds like me that are interested in such things and even have a solution where you insert a cheap capacitor into the setup to prevent the phenomenon.

For everyone else, don't panic! I think the message is just to be sure not to use particularly long wires and be sure your elderly power supply is up to specification (dust off the voltmeter perhaps?) before plugging into it with our whacky firmware cure. I believe this spike phenomenon could impact pretty much any brand of adapter out there so I’d suggest you err to the side of caution whichever TTL adapter you buy and keep your leads as short as possible. In my case they came in under 30cm (1 foot or 12 inches) total and my 650w power supply tested right at spec.

Otherwise I hope you’re all well and that winter is treating you kindly. At the moment I’m sitting in an airport headed back to Canada where I hear the snowboarding is off to a grand start this year. Remember to look up from fixing hard drives and get some fresh air when you can out there. Good holidays to you all. Cheers!

- CarterinCanada

0

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now

  • Recently Browsing   0 members

    No registered users viewing this page.