Welcome to MSFN

Register now to gain access to all of our features. Once registered and logged in, you will be able to contribute to this site by submitting your own content or replying to existing content. You'll be able to customize your profile, receive reputation points as a reward for submitting content, while also communicating with other members via your own private inbox, plus much more! This message will be removed once you have signed in.


Sign in to follow this  
Followers 0
HighDarkTemplar

Seagate Firmware Update

12 posts in this topic

Hi!

I remember seeing an article on another site about some of the Seagate Barracuda HDD's (including ST31000528AS, which is my disc) had some serious problems. There was a firmware update somewhere, but I cannot seem to find it. I also think that there was something else that you had to do to actually get it to boot and install, if someone knows what, please tell me :-)

Thanks for your time!

-Nerevar

0

Share this post


Link to post
Share on other sites
There was a firmware update somewhere, but I cannot seem to find it.

Have you checked the manufacturer's site ? It has a download button on the 1st page.

+there are three sticky about Seagate Barracuda on this very forum.

0

Share this post


Link to post
Share on other sites

Did take a look, and read a bit on the forums. But i couldn't find a download link :-(

Thanks!

0

Share this post


Link to post
Share on other sites

Thanks for that, however still not solved. It just detects my discs (which i already know about), and gives the following information:

Model: ST31000340AS, Serial: 9QJ02YHA, Firmware: SD15

Model: ST31000340AS, Serial: 9QJ04F3P, Firmware: SD15

The disc's colored in red, in that program you mentionen, which means that it has known firmware updates (which i also know). When i entered the seagate site(through the program), it didn't find any updates at all :-/ WTF??

Thanks again!

0

Share this post


Link to post
Share on other sites
Thanks for that, however still not solved. It just detects my discs (which i already know about), and gives the following information:

Model: ST31000340AS, Serial: 9QJ02YHA, Firmware: SD15

Model: ST31000340AS, Serial: 9QJ04F3P, Firmware: SD15

The disc's colored in red, in that program you mentionen, which means that it has known firmware updates (which i also know). When i entered the seagate site(through the program), it didn't find any updates at all :-/ WTF??

Thanks again!

How about using google next time?

Typed in "Seagate firmware" and ~10 seconds later I had the official Seagate page for the 7200.11 firmware updates.

http://seagate.custkb.com/seagate/crm/self...&NewLang=en

0

Share this post


Link to post
Share on other sites

Thanks for picking up that error :-) One last question, does firmware updates tend to destroy current data on the disc?

Thanks!

0

Share this post


Link to post
Share on other sites
Updated and working :-) Thanks for all the replies. Case closed :-)

Good job :D

If anything goes wrong later on, do tell us as I have just installed a 500GB 7200.11 drive with SD1A firmware into an external enclosure so I am hoping it will live for longer than a few days like it did with the SD15 firmware. If I know of others that have SD1A drives dying then I will know to be careful with what I put on it.

Edited by Zenskas
0

Share this post


Link to post
Share on other sites
Updated and working :-) Thanks for all the replies. Case closed :-)

Good job :D

If anything goes wrong later on, do tell us as I have just installed a 500GB 7200.11 drive with SD1A firmware into an external enclosure so I am hoping it will live for longer than a few days like it did with the SD15 firmware. If I know of others that have SD1A drives dying then I will know to be careful with what I put on it.

Just as a side note:

I don't think that using any Seagate 7200.11 Barracuda drive in an (most likely not active cooled) external hard drive enclosure is a particularly good idea.

Just last week I used one of my Barracudas externally to back up a good amount of data and it got VERY hot in its case while copying data for a longer period of time.

I highly doubt that this is good for the drive. However I have to say that my room temp was quite hot that day. About 27-28°C. Still I don't think that the drive would have stayed really considerably cooler, if the room-temp had been lower.

So, I would be careful with these drives when using them externally. Personally I wouldn't advise anyone to use them without sufficient cooling, unless all the drive(-s) do(-es) is idle 99% of the time.

0

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now
Sign in to follow this  
Followers 0

  • Recently Browsing   0 members

    No registered users viewing this page.