Diamondmax 22 ST3500320AS

[igirao]

Hi! I have this HDD with firmware MX15. The BIOS says that the size is 0MB and LBA Supported.

So, I tried the 0MB guide first with no luck.

F3 T>m0,2,2,,,,,22                  

LED:000000CC FAddr:0025BF67                           
LED:000000CC FAddr:0025BF67

 

Then I went through the next step for a busy state>

 

Ctrl+z

 

F3 T>/2       

F3 2>Z      

Spin Down Complete                  
Elapsed Time 0.144 msecs                        
F3 2>U      

Spin Up Complete                
Elapsed Time 11.241 secs                        
F3 2>/1       

F3 1>N1       

F3 1>/      

F3 T>m0,2,2,,,,,22                  

Error 1008 DETSEC 0000500E Process Defect List Error                                                    
R/W Sense 00000002, R/W Error 841C0087, List Offset 00000000, File Error 00000001

 

Then Ctrl+L>

 

F3 T>     
TetonST 2.0 SATA Moose Gen 3.0 (RAP fmt 10 ) w/sdff (RV )  Product FamilyId: 27, Membe                   HDA SN: 9QM8ZVPB, RPM: 7206, Wedges: 108, Heads: 4, Lbas: 3A386030, PreampType:6D 64     
PCBA SN: 00007918NX0Y, Controller: TETONST_2(639D)(3-0E-3-5), Channel: AGERE_COP                  PERHEAD_LITE, PowerAsic: MCKINLEY Rev 04, BufferBytes: 2000000                                             Package Version: MS0100.MXD1.AD090B., Package P/N: 100504103, Package Builder ID: 3K,     
Package Build Date: 01/16/2008, Package Build Time: 16:28:26, Package CFW Version: MS01.MXD1.00052452.3K00, Package SFW1 Version: B000, Package SFW2 Version: C0FE, Package SFW3 Version: C0FA, Package SFW4 Version: ---- Controller FW Rev: 01161628, CustomerRel: MX15, Changelist: 00052452, ProdType:MS01.MXD1, Date: 01/16/2008, Time: 162826, UserId: 00000761         Servo FW Rev: C0FE RAP Format Rev: 0092, Contents Rev: 15 05 11 08                                               
Features:         
- Quadradic Equation AFH enabled                                
- VBAR with adjustable zone boundaries enabled                                              
- Volume Based Sparing enabled                              
- IOEDC enabled               
- IOECC enabled               
- DERP Read Retries enabled

 

Then hit a Ctrl+C>

 

F3 T>
Spinning Down

Spin Down Complete
Elapsed Time 10.573 secs
Delaying 5000 msec

Jumping to Power On Reset
Bogus ISR

 

Are there different commands for this HDD?

 

So what's hapening with this drive that can't be restored?

Tks.

[jaclaz]

No, the disk drive is "the same" and commands/procedure are too (provided that the actual issue is the same).

 

There are three ways to do the "BSY" fix:

• remove completely the PCB and re-connect it "hot"
• insulate head contacts
• insulate motor contacts

In theory any of those should work, in practice there are reports that in some cases one of the three works where one of the other two did not.

 

BUT the:

Error 1008 DETSEC 0000500E Process Defect List Error

R/W Sense 00000002, R/W Error 841C0087, List Offset 00000000, File Error 00000001

 is not  at all a good sign.

 

Is this still the same drive:

http://www.msfn.org/board/topic/142565-how-to-solve-error-1009-detsec-00006008-fix/?p=1032082

 

or have you a fancy for Maxtor 22 drives with this specific issue?

If it is, it is not like starting a new thread will get you any added information/suggestion/help, you left that other one unfinalized, and you come back more than one year later with the same issue?

 

jaclaz

Edited December 18, 2014 by jaclaz

[igirao]

Hi Jaclaz! It's me again. Sorry to post a new thread. I thought that one was closed already.  But I came back with more precisely info, No more seagates HDD. I was seaching out my stuffs and found that HDD and thought to give it one more chance. I did all the procedures you said and none worked out. Just one moment I went through the end but it end up with an unsuccess format. Then it started to show that error. What that could mean? Bad pcb, atenuator, head or corrupted file? Please give me a good sign, will you? Please see Vicoria's picture. It says 0MB and 0LBA and on PIO mode it says bsy. What commands can we use to check it deeper? What about we both do this opearation remotely? We can use teamviwer or Skype with a webcam . Tks.

[jaclaz]

I have no idea on what can still be done in a DIY environment.

That "Error 1008" has been *somehow* reported as being a head issue, but as always happen with this kind of matters, noone really knows what he is talking about and those that actually know stay silent or post deceiving info, just for making some fun of the non-pros.

You can try if Sediv now supports that model , otherwise the only resource I can think of is that you can try asking here:

http://malthus.mooo.com/index.php?

the place is where the good guys (maybe not really pros, but friendly enough) use to gather.

jaclaz

Edited December 18, 2014 by jaclaz