[johndoe74]

Speedfan v4.35

Overview:
SpeedFan is a freeware program that monitors voltages, fan speeds and temperatures in computers with hardware monitor chips. SpeedFan can even access S.M.A.R.T. info for those hard disks that support this feature and show hard disk temperatures too, if supported. SpeedFan supports SCSI disks too. SpeedFan can even change the FSB on some hardware (but this should be considered a bonus feature). At the lowest level, SpeedFan is an hardware monitor software that can access digital temperature sensors, but its main feature is that it can change fan speeds (depending on the capabilities of your sensor chip and your hardware) according to the temperatures inside your pc, thus reducing noise.

Changelog:

• completely rewritten the detection and the identification strategy of ITE IT871xF chips (fan readings are now ok)
  
• xAP support is now properly reenabled between sessions
  
• fixed context sensitive help (F1 key) on Windows Vista
  
• enabled, if needed, the SMBus on Intel ICH7 and ICH8-M
  
• added several checks to CPU usage routines, fixing a nasty issue where an error window appeared once every second
  
• added full support for ATI SB600 SMBus
  
• added full support for Intel ICH9 SMBus
  
• added full support for nVidia MCP55 SMBus
  
• added sull support for ADT7475
  
• added nVidia Control Panel access to read video card temperatures
  
• supported the IT8716F and the IT8718F hardware monitor at unusual addresses
  
• added some SMB scan exceptions for Compal 08A0
  
• SMBus address $15 no longer scanned on AOpen i975Xa-YDG
  
• fixed an issue that caused the DFI LP UT NF4 SLI-DR Venus to power off on program start
  
• added support for Fintek F71872F voltage readings
  
• IT8712F-J now uses two undocumented FAN DIVs
  
• speeded up Asus M2N32-SLI DELUXE program startup
  
• added detection of an unknown Fintek chip (to avoid false detection of other sensors at the same address)
  
• W83627EHF and W83627DHG now properly show SMARTFAN III in CONFIGURE / ADVANCED
  
• W83627EHF and W83627DHG can now change PWM TYPE from PWM to DC in CONFIGURE / ADVANCED
  
• fixed FAN DIVISOR settings for Winbond W83791D
  
• added PWM OUT BASE CLOCK selection for WINBOND W83627DHG, W83627EHF and W83627EHG
  
• warning temperature can now be set as high as 125C in CONFIGURE

website :: Speedfan
Language :: English
File size :: 1.74 MB (1,820,580 bytes)
MD5 :: 7F913D71E92A891641BA44B3982ACF81
Main :: MediaFire
Mirror :: Badongo
Mirror :: FileFront
Mirror :: Uploading
Mirror :: ifile.it
Mirror :: divshare
Mirror :: midload
Mirror :: tods
Mirror :: Uploaded.to

This post has been edited by johndoe74: 20 August 2008 - 01:52 PM

[johndoe74]

Speedfan v4.34

File size :: 1.64 MB (1,722,188 bytes)
MD5 :: 87200FCF5279A5153697FD89C7B02BAE
Main :: Esnips
Mirror :: FileFront
Mirror :: filefactory
Mirror :: box.net
Mirror :: badongo
Mirror :: MediaFire
Mirror :: divshare
Mirror :: uploading.com
Mirror :: easy-share

This post has been edited by johndoe74: 19 August 2008 - 11:19 AM

[johndoe74]

updated to v4.34

[0d14r3]

Thanks, JD!!

[johndoe74]

updated to v4.35